Explosives

Employers

As an employer, you must ensure that:

• A blasting operation is conducted by a blaster who has an appropriate certificate of qualification that is issued under the Apprenticeship and Occupational Certification Act for the work they are doing.
• A blaster is chosen to supervise the blasting operation if there is more than 1 blaster involved with the blasting operation.
• Only a person with the appropriate certificate of qualification is chosen to conduct or supervise a blasting operation.
• A code of practice is established for the safe handling of misfired charges and make the code of practice available to a health and safety officer when requested.
• A code of practice is established for:
  • The use of black powder
  • The handling and disposal of time-expired, deteriorated, or damaged explosives,
  • Specialized blasting operations, and
  • Any other unusual use of explosives as determined by the Chief Compliance Officer.
• The cause of a misfired charge is established, as far as possible, and make sure that corrective action is taken to prevent it from happening again.
• Only an authorized employee has access to explosives.
• Nobody carries explosives in their clothing.
• No smoking or open flame is allowed within:
• 30 metres of any place where explosives are stored, or
• 15 metres of any place where an explosive is being handled, used or transported
• Primed explosives are not transported, stored, or handled inside a vehicle or near any electrical equipment.
• When electrical detonators must be transported in a vehicle equipped with a radio transmitter:
• The detonators are transported in packaging that meets the requirements of the Explosives Act (Canada) and regulations,
• If explosives are unloaded from a transport vehicle and are to be used the same day, the blasting explosives and detonator products:
• Are placed at least 50 metres apart, and
• Are locked in separate day boxes that are manufactured or certified by an engineer to be enough to protect a person from injury.
• When blasting explosives or detonator products are to be stored overnight, these items must be stored according to the Explosives Act (Canada).
• To prevent ignition or sparks:
• No article or thing that may ignite spontaneously or is likely to cause an explosion or fire is taken into or stored within 8 metres of a magazine that is used to keep or store explosives, and
• Tools and implements used to open containers of explosives are made of non-sparking materials.
• Along with the blaster, a blasting machine is inspected at least annually by a competent person, and that the blasting machine is maintained in good working condition.
• A log book is maintained that records inspections and repairs to a blasting machine and is available to a health and safety officer on request.
• No other person other than a blaster with the appropriate certificate of qualification fires a charge or a person referred to in the regulations.
• When the firing of a charge is done from power lines, the safety switch box is:
• Provided to the blaster,
• Constructed so the door may be closed and locked only in the “off” position, and
• Kept locked and is not accessible to anyone other than the blaster responsible for firing the charge
• That signs using the words “Blasting Operations – Turn Off Radio Transmitters” and “Opérations de sautage - éteindre les émetteurs radio” are used when a blasting operation by an electric means of initiation is about to commence and while it is progress. The letters of the signs must be made from luminous paint not less than 150 mm high on a contrasting background and are posted on all roads within 100 m of the blasting area.
• That signs using the words “End of Blasting” and “Fin de sautage” indicate to drivers of vehicles when they are leaving the area.
• The signs must be removed or covered after each blast is completed.
• Empty cartons and wrappings are collected from the site before blasting and disposed of after the blast is completed.
• Time-expired, surplus, or damaged explosives are disposed of according to the Explosives Act (Canada).
• Blasting mats are used when there is a hazard to people or property from flying debris.
• Loose rocks are scaled off the sides of excavations and removed from the crest after blasting and before any work begins again.

Blasters

A blaster conducting a blasting operation or as a blaster supervising the blasting operation (when there is more than one blaster) must:

• Make sure all people in or near the blasting area remain safe.
• Maintain continuous visual supervision over a person or blaster who is assisting in a blasting operation but does not hold the appropriate certificate of qualification.
• Only tools and equipment used by approval of the blaster are brought into the blasting area.

When handling explosives and related matters, the blaster must make sure:

• Blasting explosives and detonator products are kept and handled separately until the last practical moment when the blaster primes the explosive,
• The explosive is not primed where the explosives are stored,
• The primed explosives are not slit or tamped,
• The wrapping is not removed from nitroglycerine-based products,
• Explosives that are time-expired, deteriorated, or damaged are not used,
• Blasting mats are used that are adequate in size and strength to protect property and people from the danger of flyrock,
• Frozen explosives are used according to the manufacturer’s recommendations,
• Drill holes are of the right size to allow the free insertion to the bottom of the hole without ramming, pounding or undue pressure,
• Only tamping rods of wood or other non-metallic, non-sparking material are used,
• Drill holes are not tied until the last practical minute before firing and are fired in a single operation,
• Drilling is not done in a previously blasted area until the surface to be drilled is exposed and carefully examined for remnants of explosives or holes containing explosives, and
• When remnants are found, the explosives are detonated or removed before drilling begins.

When an electrical storm approaches, and until after it passes, the blaster must make sure that:

• The blasting operations stop,
• If an electric means of ignition is being used, the lead wires are short-circuited, and
• All people leave and do not enter the danger area.

No person other than a blaster with the appropriate certificate of qualification shall:

• Prime an explosive,
• Make any connection that leads or will lead from the primed charge to an initiating device,
• Connect any delay or sequencing device, or program the delay or sequence for the blast, or
• Fire a charge.

Blasters must make sure that electric detonators, before firing a charge, are:

• Tested for continuity with a blasting meter before being used,
• Tested according to the manufacturer’s specifications, and
• Shunted or short-circuited after being tested until they are connected in circuits.

Blasters must make sure that the electric blasting circuit is tested with a blasting meter for continuity and resistance before connecting an electric blasting circuit to the lead wires, and before connecting the lead wires to the power source. When electric blasting initiation is used, the blaster must make sure that:

• Only a blasting machine or safety switch box is used, and
• The blasting machine does not exceed the manufacturer’s rated capacity.

Blasters conducting the firing of a charge must make sure, before making the final connection of lead wires to the power source (when using an electric initiation) or before firing by any other initiation method, that:

• An audible warning that is a minimum of 120 dB at the source that lasts at least 30 seconds is made to all people in the danger area,
• All people have moved out of the danger area,
• All roads and approaches to the danger area are guarded to prevent anyone from entering, and
• All machines and equipment are clear from the effects of the blast.

Drill holes

The employer and blaster must make sure:

• No drilling is done at a distance equal to one and one-half times the depth of the drill hole from any drill hole containing explosives, as well as maintaining a minimum distance of 6.5 metres at all times.
• The employer establishes a code of practice when, due to the nature of the ground being drilled, it is necessary to load a drill hole immediately after drilling is complete and then drills holes must be made nearby (adjacent).

The employer and blaster must make sure the loaded drill holes in a blasting area are clearly identified and secured and protected from machines or equipment passing over them.

Seismic blasting

The employer must make sure that only biodegradable electronic explosives are used in a seismic blasting operation.

If the seismic blasting operation is done in an isolated location, the blaster may leave loaded holes unattended only when the blaster has made sure that:

• The leg wires are shunted,
• The drill cuttings are spread out and levelled,
• The leg wires are coiled as close to the ground as possible (and never longer than 15 cm above ground level), and
• The holes are suitably identified, recorded in the blasting log, and blasted within 30 days.

If a blaster can confirm that there was a complete detonation of explosives, the firing line may be left connected to the firing switch and disconnected at the hole.

A misfired or unfired charge may be left unfired only if:

• The charge is in an isolated location, at a depth deep enough to minimize the risk to others, and cannot be conventionally and safely detonated, and
• The location of the charge is marked effectively, and the employer keeps a permanent record of the location.

Extraneous electricity

The blaster must make sure that the electric initiation of blasting:

• Are kept on the ground, except for the bare connections that may be raised to prevent current leakage.
• Is not used where there is a danger from extraneous electricity or when blasting within 100 metres of electrical power lines, unless the manufacturer’s specifications indicate it is safe to do so.

The employer and blaster must each make sure that the electric initiation of blasting is not carried out at distances from any transmitter that are less than the minimum distances set by the Institute of Makers of Explosives Standard “Safety Guide for the Prevention of Radio Frequency Radiation Hazards in the Use of Commercial Electric Detonators (Blasting Caps)” (December 2011), as amended.

After Firing and Misfires

The blaster must follow the code of practice established by the employer for the safe handling of misfired charges.

The blaster who fired the charge must make sure that no person, other than the blaster, enters a danger area where the charge has been fired until the blaster conducts a thorough inspection of the site and approves the danger area as safe. An assistant may accompany the blaster when conducting the inspection. When using an electric means of initiation, the blaster must make sure that no person enters the danger area until the blaster disconnects the lead wires from the power source, short-circuits the leads, and locks the safety switch box, where applicable.

The blaster must remain outside of the danger area when a charge has misfired, or is suspected of misfiring, until 15 minutes after the last charge was expected to explode.

• When this time has expired, the blaster (who fired the charge) may enter the danger are, conduct a thorough inspection of the site, and approach the misfired (or suspected of misfired) charge to assess the situation or potential hazard.
• If no misfired charge is found, the blaster may approve the danger area as safe and sound the all clear signal of a minimum 120 dB.
• If one or more misfired charges are found, the blaster must:
• Readjust the danger area boundary if required,
• Conspicuously mark all the misfired charges, and
• Allow personnel to enter the danger area to assist in treating the misfire.

Records

The blaster who conducts or supervises a blast must maintain a log book that records the following:

• Before the blast:
• Job location,
• Names of blaster and assistants,
• Diagram of the blasting pattern and sequence of firing,
• Type and amount of blasting explosives and detonators,
• Number, depth, and placement of charges in each hole,
• Resistance calculations for each series and circuit when using electric means of initiation,
• Precautions taken to control fly rock, air blast, and ground vibrations,
• Placement of people to guard the danger area, and
• Reason for any delay in blasting.
• After the blast:
• Date and time of the blast,
• Weather conditions at the time of the blast,
• Results of the post-blast examination for misfires and other dangers, and
• When seismic blasting, results of post-blast examination for vibration and peak noise levels.

The blaster must keep a log book for three years after the last blast recorded in the book, and make the log book available to an OHS officer. The blaster must give a copy of the log book to the employer, who will keep the log book for three years after the last blast recorded in the log book, and who will make sure it is available to a health and safety officer when requested.

The blaster who conducts, supervises, or participates:

• In a blasting operation, must keep their certificate of qualification in a safe place at the place of employment, and make the certificate available to a health and safety officer.
• In a specialized blasting operation, must keep their training record in specialized blasting operations in a safe place at the place of employment, and make the certificate available to a health and safety officer.

The employer must make sure that the employee in charge of drilling maintains a log book that records the number of drilled holes, the depth of the drill hole, subdrill, and any anomalies to the drill holes, and make the log book available to a health and safety officer when requested.

Employees

As an employee, you must:

• Follow all directions and instructions given by the blaster who is responsible for the safety of persons in or near the blasting area.

General Regulation - Occupational Health and Safety Act
N.B. Reg. 91-191

Part XII EXPLOSIVES

Section 146

146. This Part does not apply to an underground mine.

Blasting operation

Section 147 Control of Blasting Operation

147. (1) An employer shall ensure that a blasting operation is conducted by a blaster who holds an appropriate certificate of qualification issued under the Apprenticeship and Occupational Certification Act for the work involved.

(1.1) Despite subsection (1), a blaster who does not hold an appropriate certificate of qualification issued under the Apprenticeship and Occupational Certification Act may conduct a specialized blasting operation if the employer ensures that the blaster is competent to do the work, and the employer shall maintain any record demonstrating the blaster’s competency for at least three years after the specialized blasting operation is completed.

(2) Where more than one blaster is involved in a blasting operation, an employer shall designate one of the blasters to supervise the blasting operation.

[N.B. Reg. 93-8, s. 2; 2024-38, ss. 77, 78]

Section 148

148. (1) No person other than a blaster with the appropriate certificate of qualification shall conduct or supervise a blasting operation.

(2) - (3) Repealed. [N.B. Reg. 2024-38, s. 79]

[N.B. Reg. 93-8, s. 3; 2024-38, s. 79]

Section 149

149. (1) A blaster who conducts a blasting operation or, where there is more than one blaster involved, the blaster who supervises the blasting operation, shall ensure the safety of all persons within and adjacent to the blasting area.

(2) All persons within or adjacent to a blasting area shall comply with the directions or instructions given by the blaster responsible for ensuring the safety of persons within or adjacent to the blasting area.

[N.B. Reg. 93-8, s. 4]

Section 150

150. (1) A person who is not a blaster or a blaster who does not hold the appropriate certificate of qualification may assist in a blasting operation.

(2) A blaster conducting or supervising a blasting operation shall exercise continuous visual supervision over a person or blaster referred to in subsection (1).

[N.B. Reg. 93-8, s. 5]

Section 150.1 Seismic blasting operation

150.1 (1) An employer shall ensure that only biodegradable electronic explosives are used in a seismic blasting operation.

(2) If a seismic blasting operation is carried out in an isolated location, loaded holes may be left unattended only if a blaster has ensured that

(a) the leg wires of the detonator are folded and shunted, the drill cuttings are spread out and levelled and the leg wires are coiled as close to the ground as possible while never exceeding 15 cm above the ground level, and

(b) the holes are suitably identified, recorded in the blasting log and blasted within 30 days after they are loaded.

(3) If a blaster can confirm complete detonation of explosives in a seismic blasting operation, the firing line may be left connected to the firing switch and dis‐ connected at the hole.

(4) A misfired charge in a seismic blasting operation may be left unfired only if

(a) the charge is in an isolated location at a depth sufficient to minimize the risk of injury to employees or other persons and cannot be conventionally and safely detonated, and

(b) the location of the charge is effectively marked and the employer keeps a permanent record of the location.

[N.B. Reg. 2024-38, s. 80]

Section 151 General Safety

151. An employer shall ensure that

(a) only an authorized employee has access to explosives,

(b) no person carries explosives in clothing,

(c) no smoking or open flame is permitted

(i) within 30 m of any place where an explosive is stored, or

(ii) within 15 m of any place where an explosive is being handled, used or transported, and

(d) primed explosives are not transported, stored or handled inside a vehicle or near any electrical equipment.

Section 152

152. Where it is necessary to transport electrical detonators in a vehicle equipped with a radio transmitter, an employer shall ensure that

(a) the detonators are transported in a package in accordance with the requirements set out in the Explosives Act (Canada) and the regulations under that Act,

(b) the radio transmitter is switched off whenever the package is open or, if the circumstances do not permit the radio transmitter to be switched off, the radio transmitter meets the requirements established by the Institute of Makers of Explosives in its publication entitled "Safety Guide for the Prevention of Radio Frequency Radiation Hazards in the Use of Commercial Electric Detonators (Blasting Caps)" (December 2011), as amended, and

(c) the detonators are transported in their original packages with their leg wires folded and shunted, as shipped by the supplier.

[N.B. Reg. 2024-38, s. 81]

Section 153 Explosives and detonotators

153. (1) If explosives are unloaded from a transport vehicle and are to be used the same day, an employer shall ensure that blasting explosives and detonator products

(a) are placed at least 50 m apart when possible, and

(b) are locked in separate day boxes that are manufactured to be sufficient to protect a person from injury or are certified by an engineer as being sufficient to protect a person from injury.

(2) Where blasting explosives or detonator products are to be stored overnight, an employer shall ensure that they are stored in accordance with the requirements of the Explosives Act (Canada).

[N.B. Reg. 2024-38, ss. 82, 83]

Section 154

154. An employer shall ensure that

(a) no article or thing liable to ignite spontaneously or likely to cause an explosion or fire is taken into or stored within 8 m of a magazine used to keep or store explosives, and

(b) tools and implements used to open containers of explosives are made only of non-sparking materials.

[N.B. Reg. 2024-38, s. 84]

Section 155

155. An employer and a blaster shall each ensure that a blasting machine is inspected at least annually by a competent person and that the blasting machine is maintained in good working condition.

[N.B. Reg. 2024-38, s. 85]

Section 155.1 Log book re blasting machine

155.1 An employer shall ensure that a log book recording inspections and repairs to a blasting machine is maintained and made available to an officer on request.

[N.B. Reg. 2024-38, s. 86]

Section 156 Handling

156. A blaster shall ensure that

(a) blasting explosives and detonator products are kept and handled separately until the last practicable moment when the blaster primes the explosive;

(b) no explosive is primed in any place where explosives are stored;

(c) primed explosives are not slit or tamped;

(d) the wrapping is not removed from nitroglycerine-based products;

(e) Repealed. [N.B. Reg. 2024-38, s. 87]

(f) Repealed. [N.B. Reg. 2024-38, s. 87]

(g) time expired, deteriorated or damaged explosives are not used;

(h) Repealed. [N.B. Reg. 2024-38, s. 87]

(i) where there is any danger to property or persons from flyrock from a blast, blasting mats of adequate size and strength are used;

(j) frozen explosives are used in accordance with the manufacturer's recommended procedure;

(k) drill holes are of sufficient size to admit the free insertion to the bottom of the hole of the explosive to be used without ramming, pounding or undue pressure;

(l) only tamping rods of wood or other non-metallic, non-sparking material are used;

(m) drill holes are not tied in until the last practicable moment before firing and are fired in a single operation;

(n) no drilling is done in a previously blasted area until the surface to be drilled is exposed and carefully examined for remnants of explosives or holes containing explosives; and

(o) where remnants of explosives or holes containing explosives are found, the explosives are detonated or removed before drilling commences.

[N.B. Reg. 93-8, s. 6; 2024-38, s. 87]

Section 157

157. At the approach of an electrical storm and until the electrical storm has passed, a blaster shall ensure that

(a) blasting operations cease,

(b) if an electric means of initiation is being used, lead wires are short-circuited, and

(c) all persons leave the danger area and no one enters the danger area.

[N.B. Reg. 93-8, s. 7]

Section 158

158. (1) An employer and a blaster shall each ensure that no drilling is done within a distance equal to one and one-half times the depth of the drill hole to any drill hole containing explosives and that notwithstanding the depth of the drill hole, a minimum distance of 6.5 m is maintained at all times.

(2) Where, due to the nature of the ground being drilled, it is necessary to load a drill hole immediately after drilling is complete and subsequently to drill adjacent holes, an employer shall establish a code of practice detailing the procedure to be followed in such a situation to ensure employee safety.

[N.B. Reg. 93-8, s. 8]

Section 159

159. An employer and a blaster shall each ensure that loaded drill holes located in a blasting area are clearly identified and secured and are protected from the passage of machines or equipment over them.

[N.B. Reg. 93-8, s. 9; 2024-38, s. 88]

Section 160

160. (1) No person shall conduct or direct any work in a blasting area without the approval of the blaster conducting the blasting operation or, where there is more than one blaster involved, the blaster supervising the blasting operation.

(2) Except for the tools and equipment used by a person who has obtained the approval required under subsection (1), a blaster shall ensure that only tools and equipment necessary to the blasting operation are brought into a blasting area.

[N.B. Reg. 93-8, s. 10]

Section 161

161. An employer shall ensure that no person other than a blaster who holds the appropriate certificate of qualification or a person referred to in subsection 150(1) fires a charge.

[N.B. Reg. 93-8, s. 11; 2024-38, s. 89]

Section 162

162. No person other than a blaster with the appropriate certificate of qualification or a person referred to in subsection 150(1) shall

(a) prime an explosive,

(b) make any connection that leads or will lead from the primed charge to an initiating device,

(c) connect any delay or sequencing device or program the delay or sequence for the blast, or

(d) fire a charge.

[N.B. Reg. 93-8, s. 12; 2024-38, s. 90]

Section 163 Before Firing

163. Before firing a charge, a blaster shall ensure that electric detonators are

(a) tested for continuity with a blasting meter before being used,

(a.1) tested in accordance with the manufacturer’s specifications, and

(b) shunted or short-circuited after being tested until they are connected in circuits.

[N.B. Reg. 93-8, s. 13; 2024-38, s. 91]

Section 164

164. Before connecting an electric blasting circuit to the lead wires and before connecting the lead wires to the power source, a blaster shall ensure that the electric blasting circuit is tested with a blasting meter for continuity and resistance as calculated.

Section 165

165. Before making the final connection of lead wires to the power source when using an electric initiation of blasting or before firing when using any other initiation method, a blaster conducting the firing of a charge shall ensure that

(a) an audible warning of a minimum of 120 dB at source lasting at least 30 seconds is given to all persons in the danger area,

(b) all persons have moved out of the danger area,

(c) all roads and approaches to the danger area are guarded in order to prevent anyone from entering, and

(d) all machines and equipment are clear of the effects of the blast.

[N.B. Reg. 93-8, s. 15; 2024-38, s. 92]

Section 166

166. (1) Where an electric initiation of blasting is used, a blaster shall ensure that

(a) only a blasting machine or a safety switch box referred to in subsection (2) is used, and

(b) the blasting machine does not exceed the manufacturer's rated capacity.

(2) Where firing of a charge is done from power lines, an employer shall ensure that a safety switch box

(a) is provided to the blaster and is constructed so that the door may be closed and locked only in the "OFF" position, and

(b) is kept locked and is not accessible to anyone other than the blaster responsible for firing the charge.

[N.B. Reg. 93-8, s. 16]

Section 167

167. (1) In this section

"extraneous electricity" means unwanted electrical energy greater than 50 mA that is present at a blasting area and that may enter an electric blasting circuit, and includes stray electrical current, static electricity, radio frequency energy and time-varying electric and magnetic fields.

(2) Where an electric initiation of blasting is used, a blaster shall ensure that electric blasting circuits are kept on the ground, except that bare connections may be elevated to prevent current leakage.

(3) A blaster shall ensure that electric initiation of blasting is not used

(a) where there is a danger from extraneous electricity, or

(b) when blasting within 100 m of electric power lines, unless the manufacturer’s specifications indicate that it is safe to do so.

[N.B. Reg. 93-8, s. 17; 2024-38, s. 93]

Section 168

168. An employer and a blaster shall each ensure that electric initiation of blasting is not carried out at a distance from any transmitter less than the minimum distances established by the Institute of Makers of Explosives in its publication entitled "Safety Guide for the Prevention of Radio Frequency Radiation Hazards in the Use of Commercial Electric Detonators (Blasting Caps)" (December 2011), as amended.

[N.B. Reg. 93-8, s. 18; 2024-38, s. 94]

Section 169 After Firing

169. (1) A blaster who fires a charge shall ensure that no person other than the blaster enters a danger area where the charge has been fired until the blaster makes a thorough inspection of the site after the charge has been fired and approves the danger area as safe.

(2) A blaster who fires a charge by an electric means of initiation shall ensure that no person enters a danger area where the charge has been fired until the blaster disconnects the lead wires from the power source, short-circuits the leads and, where applicable, locks the safety switch box.

(3) Notwithstanding subsection (1), a blaster may be accompanied by an assistant when making an inspection under subsection (1).

[N.B. Reg. 93-8, s. 19]

Section 170 Misfires

170. (1) If a charge has misfired or is suspected of having misfired, the blaster who fired the charge shall remain outside the danger area until 15 minutes after the last charge was due to explode.

(2) On expiration of the time referred to in subsection (1), the blaster who fired the charge shall enter the danger area, make a thorough inspection of the site and approach the misfired or suspected misfired charge to assess the situation or potential hazard.

(3) Where no misfired charge is found, the blaster who fired the charge may approve the danger area as safe and shall cause an all clear signal of a minimum of 120 dB at source to be sounded.

(4) Where one or more misfired charges are found, the blaster who fired the charge

(a) shall readjust the danger area boundary if required,

(b) shall inform the employer of the situation,

(c) shall conspicuously mark all misfired charges, and

(d) notwithstanding subsection 169(1), may allow sufficient personnel to enter the danger area to assist in treating the misfire.

[N.B. Reg. 93-8, s. 20; 2024-38, s. 95]

Section 171

171. (1) An employer shall establish a code of practice for the safe handling of misfired charges and shall have the code of practice available for inspection by an officer.

(2) A blaster shall follow the code of practice referred to in subsection (1).

[N.B. Reg. 93-8, s. 21]

Section 172

172. An employer shall, as far as practicable, ensure that the cause of a misfired charge is established and that corrective action is taken to prevent recurrence.

Section 173 Records

173. (1) A blaster who conducts or supervises a blast shall maintain a log book recording the following:

(a) before the blast:

(i) job location;

(ii) names of blaster and assistants;

(iii) diagram of blasting pattern and sequence of firing;

(iv) type and the amount of blasting explosives and detonators;

(v) number, depth and placement of charges in each hole;

(vi) resistance calculations for each series and circuit when using an electric means of initiation;

(vii) precautions taken to control fly rock, air blast and ground vibrations;

(viii) placement of persons to guard the danger area; and

(ix) reason for any delay in blasting; and

(b) after the blast:

(i) date and time of blast;

(ii) weather conditions at time of blast; and

(iii) results of post-blast examination for misfires and other dangers, and in the case of a seismic blasting operation, results of post-blast examination for vibration and peak noise levels.

(2) A blaster shall keep a log book referred to in subsection (1) for three years after the last blast recorded in the log book and shall make the log book available for inspection by an officer.

(3) A blaster shall provide a copy of the log book to the employer who shall keep the log book for at least three years after the last blast recorded in the log book and shall ensure it is made available to an officer on request.

[N.B. Reg. 93-8, s. 22; 97-121, s. 27; 2024-38, s. 96]

Section 174

174. A blaster who conducts, supervises or participates in a blasting operation shall keep the certificate of qualification referred to in subsection 147(1) in a safe place at the place of employment and make it available for inspection by an officer.

[N.B. Reg. 93-8, s. 23]

Section 174.1 Production of training records

174.1 A blaster who conducts, supervises or participates in a specialized blasting operation shall keep their training records in specialized blasting operations in a safe place at the place of employment and make it available to an officer on request.

[N.B. Reg. 2024-38, s. 97]

Section 174.2 Log book

174.2 (1) An employer shall ensure that the employee in charge of drilling maintains a log book recording the number of drilled holes, the depth of the drill holes and any anomalies to the drill holes.

(2) An employer shall ensure that the log book is made available to an officer on request.

[N.B. Reg. 2024-38, s. 97]

175. Repealed. [N.B. Reg. 2024-38, ss. 98, 99]

Section 176 Warning Signs

176. (1) Where a blasting operation by an electric means of initiation is about to commence and while it is in progress, an employer shall ensure that signs bearing the words "Blasting Operations - Turn Off Radio Transmitters" and "Opérations de sautage - éteindre les émetteurs radio" in letters of luminous paint not less than 150 mm high on a contrasting background are posted on all roads within 100 m of the blasting area.

(2) An employer shall ensure that signs bearing the words "End of Blasting" and "Fin de sautage" indicate to drivers of vehicles when they are leaving the area referred to in subsection (1).

(3) An employer shall ensure that the signs described in subsections (1) and (2) are removed or covered after each blast is completed.

Section 177 Explosives

177. (1) An employer shall ensure that empty explosives cartons and wrappings are

(a) collected from the site before blasting, and

(b) disposed of after the blast is completed.

(2) An employer shall ensure that time-expired, surplus or damaged explosives are disposed of in accordance with the Explosives Act (Canada).

[N.B. Reg. 93-8, s. 24; 2024-38, ss. 100, 101]

Section 178

178. An employer shall ensure that

(a) blasting mats are used where there may be a hazard to persons or property from flying debris, and

(b) loose rocks are scaled off the sides of excavations and removed from the crest after blasting and before any work is resumed.

Section 179 Code of Practice

179. An employer shall establish a code of practice with respect to

(a) the use of black powder,

(b) the handling and disposal of time-expired, deteriorated or damaged explosives,

(c) specialized blasting operations, and

(d) any use of explosives that the Chief Compliance Officer determines to be unusual.

[N.B. Reg. 2024-38, s. 102]